|
The content and scope of the communication between Q2 (device) and the automation system (controller) can be freely defined as required. For this purpose, you can select the individual modules available for data communication from the structure offered in the GSD file.
The modules are placed in the slots predetermined by the system. All modules required for cyclic data communication with Q2 are shown in the following table.
|
|
MODULE
|
SLOT
|
Input address
|
Output address
|
|
1
|
Control
|
1
|
n n+1
|
n n+1
|
|
2
|
Inputs/outputs
|
2
|
n n+1
|
|
|
3
|
Flame signal
|
3
|
n
|
|
|
4
|
Actuator
|
4
|
n
|
n
|
|
5
|
Display
|
5
|
n n+1
|
|
|
6
|
Configuration
|
6
|
n
|
n
|
|
SLOT 1
|
CONTROL MODULE
DEVICE → CONTROLLER
|
|
|
BIT
|
CURRENT STATUS
|
FORMAT
|
NOTE
|
|
BYTE n
|
0
|
DEVICE ON
|
BOOL
|
Q2 connected and responding
|
|
1
|
STANDBY
|
BOOL
|
The device is in STANDBY
|
|
2
|
LOCKOUT
|
BOOL
|
The device is in LOCKOUT
|
|
3
|
VPS FAILURE
|
BOOL
|
Lockout due to leakage test failure
|
|
4
|
MANUAL SHUTDOWN
|
BOOL
|
Device has been put out of service locally
|
|
5
|
CONTROLLED SHUTDOWN
|
BOOL
|
Burner was turned off upon request
|
|
6
|
AIR PRESSURE WAITING
|
BOOL
|
The cycle is waiting for air pressure
|
|
7
|
POST-COMBUSTION
|
BOOL
|
Burner off waiting for the flame quenching
|
|
BYTE n+1
|
0
|
PRE-OPERATION
|
BOOL
|
Valve proving and pre-purge in progress
|
|
1
|
IGNITION
|
BOOL
|
Burner ignition in progress
|
|
2
|
STAGE 2
|
BOOL
|
Burner on, stage 2 low temperature
|
|
3
|
STAGE 3
|
BOOL
|
Burner on, stage 3 low temperature
|
|
4
|
STAGE 4
|
BOOL
|
Burner on, stage 4 low temperature
|
|
5
|
STAGE 5
|
BOOL
|
Burner on, stage 5 high temperature
|
|
6
|
STAGE 6
|
BOOL
|
Burner on, stage 5 high temperature
|
|
7
|
POST-OPERATION
|
BOOL
|
Valve proving and post-purge in progress
|
|
SLOT 1
|
CONTROL MODULE
CONTROLLER → DEVICE
|
|
|
BIT
|
Command
|
Action
|
FORMAT
|
|
BYTE n
|
0
|
UNLOCK
|
Set to1 and then to 0, emulating a push button, to reset from lockout
|
BOOL
|
|
1
|
RUN
|
0 = stop burner
1 = start burner 1
|
BOOL
|
|
2
|
AIR OUTPUT
|
0 = air valve output OFF
1 = air valve output ON 2
|
BOOL
|
|
3
|
OS OUTPUT
|
0 = shutter output OFF
1 = shutter output ON 3
|
BOOL
|
|
4
|
HT confirmation
|
Confirm the request for indirect flame surveillance (high temperature mode) 4
|
BOOL
|
|
5
|
CFG LED
|
Orange indicator
|
BOOL
|
|
6
|
OUTPUT 1
|
0 = output 1 OFF
1 = output 1 ON
|
BOOL
|
|
7
|
OUTPUT 2
|
0 = output 2 OFF
1 = output 2 ON
|
BOOL
|
|
BYTE n+1
|
0
|
NONE
|
No forced stage, cycle deploys normally
|
BOOL
|
|
1
|
STAGE 2
|
Move to stage 2 5
|
BOOL
|
|
2
|
STAGE 3
|
Move to stage 3 5
|
BOOL
|
|
3
|
STAGE 4
|
Move to stage 4 5
|
BOOL
|
|
4
|
STAGE 5
|
Move to stage 5 5
|
BOOL
|
|
5
|
STAGE 6
|
Move to stage 6 5
|
BOOL
|
|
6
|
NOT USED
|
|
BOOL
|
|
7
|
NOT USED
|
|
BOOL
|
1 No effect if the device is in LOCKOUT or MANUAL SHUTDOWN.
2 If allowed in the current stage.
3 Generic output, if not used for optical shutter control.
4 If required by configuration (parameter G08) activate periodically within 5 minutes.
5 If bits 1 to 5 are set simultaneously, the priority is always the lower one.
|
SLOT 2
|
INPUTS/OUTPUTS MODULE
DEVICE → CONTROLLER
|
|
|
BIT
|
DESCRIPTION
|
FORMAT
|
NOTE
|
|
BYTE n
|
0
|
AIR PRESSURE SWITCH INPUT
|
BOOL
|
0 = insufficient air pressure
1 = air pressure OK
|
INPUTS (STATUS)
|
|
1
|
FUEL PRESSURE SWITCH INPUT
|
BOOL
|
0 = insufficient fuel pressure
1 = fuel pressure OK
|
|
2
|
HT INPUT
|
BOOL
|
0 = High temperature mode
1 = Low temperature mode
|
|
3
|
NOT USED
|
BOOL
|
always 0
|
|
4
|
NOT USED
|
BOOL
|
always 0
|
|
5
|
NOT USED
|
BOOL
|
always 0
|
|
6
|
INPUT 1
|
BOOL
|
0 = input off
1 = input on
|
|
7
|
INPUT 2
|
BOOL
|
0 = input off
1 = input on
|
|
BYTE n+1
|
0
|
AIR OUTPUT
|
BOOL
|
0 = air valve VA off
1 = air valve VA on
|
OUTPUTS S (TATUS)
|
|
1
|
VS OUTPUT
|
BOOL
|
0 = fuel valve VS off
1 = fuel valve VS on
|
|
2
|
VB OUTPUT
|
BOOL
|
0 = fuel valve VB off
1 = fuel valve VB on
|
|
3
|
V1 OUTPUT
|
BOOL
|
0 = fuel valve V1 off
1 = fuel valve V1 on
|
|
4
|
V2 OUTPUT
|
BOOL
|
0 = fuel valve V2 off
1 = fuel valve V2 on
|
|
5
|
OS OUTPUT
|
BOOL
|
0 = shutter output off
1 = shutter output on
|
|
6
|
OUTPUT 1
|
BOOL
|
0 = output 1 off
1 = output 1 on
|
|
7
|
OUTPUT 2
|
BOOL
|
0 = output 2 off
1 = output 2 on
|
|
SLOT 3
|
FLAME SIGNAL MODULE
DEVICE → CONTROLLER
|
|
|
BIT
|
DESCRIPTION
|
FORMAT
|
NOTE
|
|
BYTE n
|
0
|
Flame 1 signal
|
DEC
|
0…99 (255) µA
|
|
1
|
|
2
|
|
3
|
|
4
|
|
5
|
|
6
|
|
7
|
|
BYTE n+1
|
0
|
Flame 2 signal
|
DEC
|
0…99 (255) µA
|
|
1
|
|
2
|
|
3
|
|
4
|
|
5
|
|
6
|
|
7
|
|
SLOT 4
|
ACTUATOR
DEVICE → CONTROLLER
|
|
|
BIT
|
DESCRIPTION
|
FORMAT
|
NOTE
|
|
BYTE n
|
0
|
Current actuator position
|
DEC
|
0…100 (255)
0…100%
|
|
1
|
|
2
|
|
3
|
|
4
|
|
5
|
|
6
|
|
7
|
|
SLOT 4
|
ACTUATOR
CONTROLLER → DEVICE
|
|
|
BIT
|
DESCRIPTION
|
FORMAT
|
NOTE
|
|
BYTE n
|
0
|
Required actuator position
|
DEC
|
0…100 (255)
|
|
1
|
|
2
|
|
3
|
|
4
|
|
5
|
|
6
|
|
7
|
|
SLOT 5
|
DISPLAY
DEVICE → CONTROLLER
|
|
|
BIT
|
DESCRIPTION
|
FORMAT
|
NOTE
|
|
BYTE n
|
0
|
Current RED display
|
HEX
|
00…FF
|
|
1
|
|
2
|
|
3
|
|
4
|
|
5
|
|
6
|
|
7
|
|
BYTE n+1
|
0
|
Current BLUE display
|
HEX
|
00…FF
|
|
1
|
|
2
|
|
3
|
|
4
|
|
5
|
|
6
|
|
7
|
|
SLOT 6
|
SETTINGS MODULE
CONTROLLER → DEVICE
|
|
|
BIT
|
CURRENT STATUS
|
FORMAT
|
NOTE
|
|
BYTE n
|
0
|
NOT USED
|
BOOL
|
0
|
|
1
|
NOT USED
|
BOOL
|
0
|
|
2
|
PROFINET DISCONNECT
|
BOOL
|
0: CONTINUE USING LAST CONDITION
1: BURNER OFF (HALT)
|
|
3
|
PROFINET NOT CONFIGURED
|
BOOL
|
|
4
|
NOT USED
|
BOOL
|
|
|
5
|
NOT USED
|
BOOL
|
|
|
6
|
NOT USED
|
BOOL
|
|
|
7
|
NOT USED
|
BOOL
|
|
|
SLOT 6
|
CONFIGURATION MODULE
DEVICE → CONTROLLER
|
|
|
BIT
|
CURRENT STATUS
|
FORMAT
|
NOTE
|
|
BYTE n
|
0
|
NOT USED
|
BOOL
|
0
|
|
1
|
NOT USED
|
BOOL
|
0
|
|
2
|
PROFINET DISCONNECT
|
BOOL
|
0: CONTINUE USING LAST CONDITION
1: BURNER OFF (HALT)
|
|
3
|
PROFINET NOT CONFIGURED
|
BOOL
|
|
4
|
TRANSPARENT MODE
|
BOOL
|
0: DISABLED
1: ENABLED 1
|
|
5
|
NOT USED
|
BOOL
|
|
|
6
|
NOT USED
|
BOOL
|
|
|
7
|
NOT USED
|
BOOL
|
|
1 When TRANSPARENT MODE is enabled, inputs to the controller are rendered, but all outputs sent from the controller to the device are ignored. This mode is enabled/disabled from webserver interface.
|